A Tank Tee is a fitting with multiple connections and accessory ports, when used the installation is neat and lightweight. There are two line contacts, one for the inlet provide line from the pump / well, another connects to the discharge line to the plumbing system. 4 FPT item ports for a pressure switch, pressure gauge, relief valve and drain device eliminate the necessity for getting several fittings and nipples which add clutter around a pressure tank.
Kinds of Tank Tees
Tank tees can be purchased in various lengths brief (3”) to long (16”) to work with the link sizes and locations on various brand names of stress tanks. The two major design kinds are Union and Non-union which may be referred to as strong or 1-item tank tees. These come in 1” and 1-¼” with male or female tank connections. Regardless tank tees are designed for hooking up to the pre-billed pressure tanks. Tank tee duration measurements are Middle-Finish-Lengths (CEL)
Are used on pressure tanks using the tank link protruding with the part of the tanks base. Short tees range from 3” to 4-1/2” CEL. Brief tank tees can be found in several types of tank link as shown listed below.
Long Tees Tank
Are employed on pressure tanks using the tank connection being either in the middle or counteract inside the base of the tanks base. Long tanks tees have men NPT tank link and are available in a number of lengths. For a longer time tank tees are essential because the size from the pressure tank selected increases, the CEL should be sufficient to increase the tee head out significantly sufficient so the pressure switch can threaded on or off without getting in touch with pressure tank. Diagram, technology drawing
Union vs. Non-Union Tank Tees
The advantages of union tank tees are recognized during initial set up, and considerably decreases the work included for tank substitute. A union kind tee easily disconnects the old tank, which can be eliminated in minutes departing all the line and item contacts and wiring intact. The newest tank can then be installed with all the tank tee lower leg from your aged tank, set in place and reconnected towards the tank tee head by tightening the union. Task finished!
Union tees that incorporate an O-ring provide a dependable watertight seal. No need to concern yourself with the connection seeping. It is suggested to pick a quality tank tee that utilizes a North American regular O-diamond ring which can easily be bought in case a substitute is ever needed.
Non-union tank tees carry out the exact same job, are less money and save cash on the acquisition cost. Nevertheless, they just do not have the identical easy set up and time conserving advantages specially when a tank has to be replaced. An added work included throughout installation or tank substitute will significantly surpass the initial savings on the tee.
Stainless Steel Tank Tees
Stainless-steel tank tees more price aggressive than No-Lead Bronze and therefore are changing bronze (red brass) tank tees since the creation of No-Lead specifications in 2014. Usually cast from 304 stainless that is incredibly long lasting and very corrosion resistant. Although stainless steel tees can be more expensive than brass, they do not include zinc alleviating the issues with dezincification that can happen when using brass alloy tank tees in intense water conditions. Another advantage will be the very high strength of stainless steel virtually eliminates all risk of stress cracking when threading into woman contacts.
Brass Alloy Tank Tees
Brass tank tees are cheaper and are best for installations in many locations. However brass alloys2-07TK-25SF-2NL are certainly not as rust resistant as stainless-steel, therefore installations in places that the water is very corrosive to brass, it is recommended to upgrade to stainless.
Galvanized Tank Tees
Galvanized tees are less costly than both stainless and brass tank tees. Their use is typically07HC125G confined to installs on galvanized stress tanks with no bladder. Galvanized tees are selected to eliminate the potential risk of galvanic rust between different metals. Galvanized tank tees utilized together with galvanized nipple and fixtures kpgpeg the problem. It is important to note that some plumbing codes do not allow the usage of galvanized fittings and nipples, one should verify that galvanized tank tees fulfill all of the applicable plumbing code requirements.
Pvc material Tank Tees
Pvc material tank tees are a really competitive option when compared with stainless-steel, brass, and07PT-25-2 galvanized materials. They may be extremely resistant to rust, they may not be as durable as metal tank tees, neither are there numerous configurations readily available. They may be considered a really appropriate option, when appropriate PVC installation practices are implemented, using a higher-quality line sealant paste instead of PTFE line sealant adhesive tape and avoiding over tightening will reduce the potential risk of more than stressing the female NPT accessory ports.